Page 8 - Haddo_Balustrading

dem HADD CAT 09 ARTWORK 121-128 26/5/09 11:01 Page 122

ARCHITECTURAL STONEWORK THE STANDARD RANGE

BALUSTRADING REGENCY URN
A530
377 (14 7 ⁄8")
279 (11")
Installation Details C E
We recommend that non-ferrous fixings (not supplied) be incorporated PIER CAP RAIL
at all rail joints and in horizontal beddings in all cases. All balusters are
supplied with stainless steel dowels for installing to rails and plinths.
All rails, plinths and under-copings are supplied in standard lengths, BALUSTER
cutting and drilling to final specification to be undertaken by your PIER
SHAFT
installation contractor.
Professional advice should be taken particularly where Building
Regulations / Codes and local bye-laws need to be complied with. It is
recommended that, if pier shafts are in-filled with concrete, the shaft
PIER BASE PLINTH
section should be lined with polystyrene (Styrofoam) or similar to act as
337 (13 ⁄4") 6 ( 1 ⁄4")
1
an isolating medium.
Y (BAY LENGTH)
Haddoncraft Forge has a range of wrought iron Baluster Bars for use in
X (OVERALL BASE DIMENSION)
conjunction with Haddonstone balustrading, see image below. The bars 20 ( 13 ⁄16") 20 ( ⁄16")
13
can be used to meet Building Regulation spacing requirements. C = Centre Baluster Spacing. E = End Baluster Spacing
PS style with K610G Balusters and T920 Under-Copings
It is most important to refer to Tech Sheet GAR1 to ensure correct
installation. Standard assembly recommendations and typical details
are available on request. Please ask for the relevant Tech Sheet.
Cutting Recommendations: General Assembly:
TS Tech Sheet No. B50 TS Tech Sheet No. GAR1

TABLE A
For normal baluster spacing: approx. 305mm (12") centres
Select highest band available unless there are other overriding factors
Bay Lengths Rails/Plinths
Band (centreline to (centreline to No. of 900mm (35 ⁄16") Balusters
7
centreline of centreline of long rails/plinths
piers) in mm piers) in inches and under-copings
where applicable)
5
1 -829 -32 /8" 1 1
7
2 830-1129 32 /16"-44 ⁄16" 1 2
11
1
3 1130-1249 44 /2"-49 ⁄16" 1 3
3
1
1
4 1250-1429 49 /4"-56 ⁄4" 2 3
5
1
5 1430-1729 56 /16"-68 ⁄16" 2 4
6 1730-2029 68 /8"-79 ⁄8" 2 5
7
1
13
15
7 2030-2155 79 /16"-84 ⁄16" 2 6
11
8 2156-2329 84 /8"-91 ⁄16" 3 6
7
9 2330-2629 91 /4"-103 ⁄2" 3 7
3
1
9
10 2630-2929 103 /16"-115 ⁄16" 3 8
5
1
3
11 2930-3061 115 /8"-120 ⁄2" 3 9
12 3062-3229 120 /16"-127 ⁄8" 4 9
9
1
15
3
13 3230-3529 127 /16"-138 ⁄16" 4 10
14 3530-3829 139"-150 ⁄4" 4 11
3
15 3830-3967 150 /16"-156 ⁄8" 4 12
1
13
This table has been compiled to give an approximate Centre Baluster Spacing
(see diagram) of 305mm (12") and a fixed End Baluster Spacing of 200mm (8").
FS style with K724G Balusters Haddoncraft Forge Baluster Bar
122 Custom-made products are available on request.